pregleda

♦ 84X48 Nokia 5110 LCD display ♦


Cena:
500 din
Želi ovaj predmet: 20
Stanje: Nekorišćen
Garancija: Ne
Isporuka: Lično preuzimanje
Plaćanje: Lično
Grad: Beograd-Sremčica,
Beograd-Čukarica
Prodavac

kraguljac (2864)

100% pozitivnih ocena

Pozitivne: 6377

  Pošalji poruku

Svi predmeti člana



Proizvedeno u : Aziji

84X48 Nokia 5110 LCD displej sa plavim pozadinskim svetlom.
Veoma upotrebljiv za povezivanje sa mikrokontrolerima , arduino i drugim razvojnim sistemima.

Note:
1. `LIGHT` linked with GND, the backlight to be lit.
2. Need you to compress the screen and PCB tighter, might got loose after the delivery.
3 Use a 3.3V controller, otherwise the display could be quite vague.

Note:

1. `LIGHT` linked with GND, the backlight to be lit.

2. Need you to compress the screen and PCB tighter, might got loose after the delivery.

3 Use a 3.3V controller, otherwise the display could be quite vague.

LCD5110 Module:

Power supply voltage:2.7V-3.3V,5V is OK,but part of the screen becomes black when tested
Data interface level:2.7-5V
Backlight power supply voltage:highest 3.3V
Module size:43.6mm x 43.1mm(width X height)
Installation diameter:2mm
Backlight:Blue


1.RST--------- reset
2.CE------------chip selection
3.DC-----------data/commands choice
4.DIN-----------serial data line
5.CLK------------serial Clock Speed
6.3.3V------------VCC
7.LIGHT--------- backlight control terminal
8.GND-----------power negative

Features:

84 X 84 dot matrix LCD,can show 4 lines of characters
Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting time.
Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace.
LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small
Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode.

NAPOMENA: U SLUCAJU TAKVOG DOGOVORA SALJEM POSTEXPRESOM PONEDELJKOM I CETVRTKOM.

Ako dodje do bilo kakvog problema kontaktirajte me i resicemo ga.

Pogledajte moje ostale aukcije:
http://www.limundo.com/Clan/kraguljac/SpisakAukcija
http://www.kupindo.com/Clan/kraguljac/SpisakPredmeta

Predmet: 19533785
84X48 Nokia 5110 LCD displej sa plavim pozadinskim svetlom.
Veoma upotrebljiv za povezivanje sa mikrokontrolerima , arduino i drugim razvojnim sistemima.

Note:
1. `LIGHT` linked with GND, the backlight to be lit.
2. Need you to compress the screen and PCB tighter, might got loose after the delivery.
3 Use a 3.3V controller, otherwise the display could be quite vague.

Note:

1. `LIGHT` linked with GND, the backlight to be lit.

2. Need you to compress the screen and PCB tighter, might got loose after the delivery.

3 Use a 3.3V controller, otherwise the display could be quite vague.

LCD5110 Module:

Power supply voltage:2.7V-3.3V,5V is OK,but part of the screen becomes black when tested
Data interface level:2.7-5V
Backlight power supply voltage:highest 3.3V
Module size:43.6mm x 43.1mm(width X height)
Installation diameter:2mm
Backlight:Blue


1.RST--------- reset
2.CE------------chip selection
3.DC-----------data/commands choice
4.DIN-----------serial data line
5.CLK------------serial Clock Speed
6.3.3V------------VCC
7.LIGHT--------- backlight control terminal
8.GND-----------power negative

Features:

84 X 84 dot matrix LCD,can show 4 lines of characters
Use serial interface communicate with the master processor,the number of interface signal line reduced greatly, only 8 signal lines including power and GND.Support different types of MCU,such as the SPI,MCS51 serial mode 0 of AVR.Transfer rate up to 4Mbps,can full speed write display data without waiting time.
Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace.
LCD controller/driver chip has been bound to LCD chip,the volume of LCD is small
Low power supply,the working current in normal situation is lower than 200μA,and has power-down mode.
19533785 ♦ 84X48 Nokia 5110 LCD display ♦

LimundoGrad koristi kolačiće u statističke i marketinške svrhe. Nastavkom korišćenja sajta smatramo da ste pristali na upotrebu kolačića. Više informacija.