Proizvedeno u : Aziji
Proizvođač: COLDheat

COLDheat hladna bezicna lemilica

bezicna baterijska lemilica koristi 4 AA baterije

! ZA LEMLJENJE FINIH KONTAKATA MALIH PRESEKA ( DO 0,5 mm )

za lemljenje konektora i tankih provodnika do 0,25 kvadrata foto 4

` The correct way to solder is to get the wires together, preferably twisted together, and then pull the solder through with minimal solder. I do mostly small things -- cars and computers -- and I end up burning the wire, globing solder all over, and doing a horrible job. This unit is PERFECT for that small niche -- fine thin wires that are hard to solder with heavier duty irons. A little practice is needed to learn to uses it -- took me 15 minutes. You cannot push hard, but on tiny little wires you done need to. All I had to do is put the iron on one side of the connection, the solder on the other, and wait a second . . . it suck the solder through the connection and you get a clean nice solder. And the iron is not hot so it is safe and if you are working under-dash in an old car you have no danger of damaging anything. You cannot melt insulation or anything -- it requires metal to metal. It is worthless for large jobs with large wires with large amount of solder. So take it for what it is made to do - fine work without major skill. I have made the best connections in my life with this tool. I keep the big ones for what they are good for. I think much of the criticism is either from professionals that really can do better with a pro model, or people trying to use it where it is not meant to be used *heavy big wire* -- so if you just need an occasional job on small stuff this is a great tool for no money. If you are a pro or are working on big wires, it is the wrong tool for the job. Which is no reason to give it a bad rating -- just understand what it is for. `
Gugl prevodilac:
Ispravan način lemljenja je spojiti žice zajedno, po mogućnosti upletene, a zatim provući lem s minimalnim lemljenjem. Uglavnom radim male stvari -- automobile i računala -- i na kraju spalim žicu, zalemim svuda i odradim užasan posao. Ova jedinica je SAVRŠENA za tu malu nišu -- fine tanke žice koje je teško lemiti težim glačalima. Potrebno je malo vježbe da biste ga naučili koristiti - trebalo mi je 15 minuta. Ne možete snažno gurati, ali na sitnim žicama morate. Sve što sam trebao učiniti je staviti željezo na jednu stranu spoja, lem na drugu, i pričekati sekundu . . . usisa lem kroz spoj i dobijete čist lijep lem. I glačalo nije vruće pa je sigurno i ako radite ispod instrumenta u starom autu nemate opasnosti da bilo što oštetite. Ne možete otopiti izolaciju ili bilo što drugo - to zahtijeva metal do metala. Bezvrijedan je za velike poslove s velikim žicama s velikom količinom lema. Zato ga uzmite za ono za što je stvoren – fini rad bez veće vještine. Napravio sam najbolje veze u svom životu s ovim alatom. Velike čuvam za ono za što su dobri. Mislim da veliki dio kritika dolazi ili od profesionalaca koji stvarno mogu bolje s profesionalnim modelom ili ljudi koji ga pokušavaju koristiti tamo gdje nije namijenjen za korištenje *teška velika žica* -- pa ako vam je potreban samo povremeni posao na male stvari ovo je izvrstan alat za bez novca. Ako ste profesionalac ili radite na velikim žicama, to je pogrešan alat za posao. Što nije razlog da mu date lošu ocjenu - samo shvatite čemu služi. `


link uputstvo na youtube:

https: // youtube. com/watch? v=NZlVV-5vVKI

Isporucuje se bez baterija