pregleda

HF TTL DTL CMOS Logic Probe LP-1


Cena:
2.950 din
Stanje: Nekorišćen
Garancija: Ne
Isporuka: AKS
BEX
City Express
DExpress
Post Express
Lično preuzimanje
Plaćanje: Pouzećem
Lično
Grad: Apatin,
Apatin
Prodavac

DIKICDJ (1821)

100% pozitivnih ocena

Pozitivne: 2236

  Pošalji poruku

Svi predmeti člana


Kupindo zaštita

Proizvedeno u : Aziji
Vrsta: Digitalni
Proizvođač: Made in China

Ovaj logički tester je namenjen za proveru električnih kola i visokofrekventnih komponenata.

Tehničke karakteristike:

Namenjen za DTL, TTL i CMOS
Visokofrekventni odgovor
Memorisanje pulsa

Usage:
1. Connect RED clip to + terminal and BLACK clip to - terminal of the power source of the circuit under test. The supply voltage should not exceed 18V DC
2. For TTL and DTL, set the upper select switch to the side marked `TIL`
For CMOS, set the upper select switch to the side marked `CMOS`, contact the probe pin to the point to be tested. The LEDs will indicate its logic states:
A) ALL LEDs OFF -High impedance
B) RED LED ON - High State (1)
C) Green LED ON - low State (0)
D) Orange LED ON - Pulse
3. For deteching and storing pulse or level transition, set lower select switch to side marked `PULSE` first. Contact the probe pin to the poin to be tested. The LEDs will indicate is basic state. Then set the lower select switch to side marked `MEM`, The orange LED will light when any pulse or level transition is detected. The pulse direction, in comparison with the original basic, state, cabe determined. After use, reset logic probe by setting the lower select switch back to side marked `PULSE`

Šifra: G1032

USLOVI PRODAJE:

ARTIKLE NE ŠALJEM VAN TERITORIJE REPUBLIKE SRBIJE!
Kupac plaća artikal, pouzećem, zajedno sa poštarinom. Reklamacije primam, preko ovih poruka, sedam dana nakon prijema artikla. Nakon isteka ovog roka, ne primam reklamacije.

Predmet: 67236221
Ovaj logički tester je namenjen za proveru električnih kola i visokofrekventnih komponenata.

Tehničke karakteristike:

Namenjen za DTL, TTL i CMOS
Visokofrekventni odgovor
Memorisanje pulsa

Usage:
1. Connect RED clip to + terminal and BLACK clip to - terminal of the power source of the circuit under test. The supply voltage should not exceed 18V DC
2. For TTL and DTL, set the upper select switch to the side marked `TIL`
For CMOS, set the upper select switch to the side marked `CMOS`, contact the probe pin to the point to be tested. The LEDs will indicate its logic states:
A) ALL LEDs OFF -High impedance
B) RED LED ON - High State (1)
C) Green LED ON - low State (0)
D) Orange LED ON - Pulse
3. For deteching and storing pulse or level transition, set lower select switch to side marked `PULSE` first. Contact the probe pin to the poin to be tested. The LEDs will indicate is basic state. Then set the lower select switch to side marked `MEM`, The orange LED will light when any pulse or level transition is detected. The pulse direction, in comparison with the original basic, state, cabe determined. After use, reset logic probe by setting the lower select switch back to side marked `PULSE`

Šifra: G1032
67236221 HF TTL DTL CMOS Logic Probe LP-1

LimundoGrad koristi kolačiće u statističke i marketinške svrhe. Nastavkom korišćenja sajta smatramo da ste pristali na upotrebu kolačića. Više informacija.