Cena: |
799 din
(Predmet je prodat)
|
Stanje: | Nekorišćen |
Garancija: | Ne |
Isporuka: | AKS Post Express |
Plaćanje: | Tekući račun (pre slanja)
Ostalo (pre slanja) |
Grad: |
Leskovac, Leskovac |
Proizvedeno u : Aziji
Šaljem i pouzećem kupcima BEZ NEGATIVNIH ocena ili bar sa manje od 2% negativnih ocena!
Opis uređaja:
Digitalni termostat HSW1209WK za kontrolu grejanja ili hlađenja u opsegu -50-110°C
Specifikacija:
Model: HSW1209WK
Dimenzije prednje ploče: 48 x 29 mm
Dimenzije rupe za ugradnju: 46 x 26.5 mm
Način kontrole temperature: uključeno / isključeno
Opseg kontrole: -50-110 ℃
Rezolucija: Kada je temperatura između -9.9~99.9℃, rezolucija je 0.1℃, van tog opsega je 1℃
Preciznost merenja: 0.1 ℃
Podešavanje Histereze u koracima od: 0.1℃
Vreme uzorkovanja: 0.5 sec.
Napajanje: DC 12V, doplata 400 din. za adapter za napajanje na AC 220V
Potrošnja u mirovanju: ≤ 35mA, i kada je uključen izlaz ≤ 65mA
Izlaz: rele DC 12V 10A, max. 125V AC
Senzor: NTC (10K 0.5%) vodootporan (ide uz uredjaj)
Uslovi rada modula: temperatura -10 ~ 60 ℃ ,vlažnost 20% -85%
Napomena: ne preporučujem direktno priključenje potrošača na ugrađeni rele, već preko jačeg relea, sklopke, elektronskog relea (SSR),...
Preporučeni dodatni - jači relei, običan i elektronski:
http://www.kupindo.com/Elektronika/23468013_RELE-12V-kalem-max-30A-250V-kontakt-
http://www.kupindo.com/Elektronika/24214309_SSR-40-DA-Solid-State-Relay-elektronski-rele
Podešavanje:
1. Podešavanje temperature je jednostavno, pritisnite dugme SET (gornje dugme) na kratko i dugmićima SET (kao +) i C/F (kao -) podesite željenu temperaturu. Sačekate oko 3 sekunde i automatski će se memorisati.
2. Za podešavanje načina rada uredjaja pritisnite dugme SET nekoliko sekundi. Na displeju se pojavi P0, zatim istovremeno na kratko pritisnite oba tastera (SET i C/F). Zatim gornjim ili donjim tasterom podesite mod rada (H - grejanje, C - hladjenje). Sačekate oko 3 sekunde i automatski će se memorisati.
3. Ako pritisnete SET duže dok se pojavi P0, a onda ponovo pritisnete SET na kratko pojaviće se P1. Zatim istovremeno na kratko pritisnite oba tastera (SET i C/F). Zatim gornjim ili donjim tasterom podesite histerezu tj. razliku temperature izmedju uključenja i isključenja. Podešavanje je moguće u koracima od 0,1 stepen. Sačekate oko 3 sekunde i automatski će se memorisati.
...itd.
P0 - mod rada, kontrola grejanja (H) ili hladjenja (C)
P1 - Histereza - razlika u stepenima izmedju uključenja/isključenja
P2 - ...
Početnici treba samo da podese P0, ostalo bolje da ne diraju, jer je fabrički podešeno za većinu namena.
Kada završite podešavanje posle nekoliko sekundi uredjaj automtski prelazi u radni režim.
To Set Celsius or Fahrenheit:
When not in programming mode, the C/F switches between Celsius and Fahrenheit.
To Set Temperature:
Press SET to enter temperature setting mode. Set temperature will flash. Use the SET and C/F buttons to select the desired temperature (when in temperature setting mode, SET and C/F function as + and -). Temperature selection will automatically confirm after 3 seconds.
To Program:
Press and hold SET for 5 seconds to enter programming mode. From programming mode, use SET and C/F (+ and -) to navigate parameters P0 through P8. Once the desired parameter is reached (P0-P8), press SET and C/F at the same time to confirm. At this time your selection will flash. Use SET and C/F to navigate through your options. Press SET and C/F at the same time to confirm your choice.
Code Description Setting Range
Factory Setting
P0 Heating / cooling H/C C
P1 Return difference 0.1-30 2.0
P2 Set upper limit 110 110
P3 Set lower limit -50 -50
P4 Temperature correction -15-15 0
P5 Delay start 0-10 0
P6 High temperature alarm -50-110
P7 Celsius / Fahrenheit (this can also be done by pressing the C/F button) CS/FH CS
P8 Factory reset (this can also be done by holding SET and C/F at the same time for an extended length of time) ON-OFF OFF
Example:
I want to use this to control a heat source for an incubator to hatch chicken eggs. I want the temperature to stay between 99.5 and 100 degrees Fahrenheit.
Step 1, Switch to Fahrenheit: • Press C/F once.
Step 2, Switch to Heating mode: • Press and hold SET for 5 seconds to enter programming mode. • From programming mode, use SET and C/F (+ and -) to navigate to P0. • Press SET and C/F at the same time to confirm. At this time the current selection will flash. • Use SET and C/F to select H (heat). • Press SET and C/F at the same time to confirm your choice.
Step 3, Set Return Difference: This determines how much the temperature rises before the heat source is turned off. Setting this at the lowest setting (some units allow a setting of 0) might result in the heat source turning off and on rapidly, running the risk of burning out the heat source prematurely. In this case, I want the heat source to turn on when the temperature falls below 99.5 and turn off when the temperature reaches 100 (Return Difference of 0.5). • Press and hold SET for 5 seconds to enter programming mode. • From programming mode, use SET and C/F (+ and -) to navigate to P1. • Press SET and C/F at the same time to confirm. At this time the current selection will flash. • Use SET and C/F to select 0.5. • Press SET and C/F at the same time to confirm your choice.
Step 4, Set temperature to 100: • Press SET (temperature setting will flash). • Use the SET and C/F buttons to set display to 100. • Wait 3 seconds to confirm.
KEY: digitalni termostat termoregulator
POZICIJA: 00009